- Jul 04, 2024
-
-
Lu Baolu authored
Replace iommu_domain_alloc() with iommu_paging_domain_alloc(). Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/20240610085555.88197-5-baolu.lu@linux.intel.com Signed-off-by:
Will Deacon <will@kernel.org>
-
Lu Baolu authored
Replace iommu_domain_alloc() with iommu_paging_domain_alloc(). Signed-off-by:
-
Lu Baolu authored
If the iommu driver doesn't implement its domain_alloc_user callback, iommufd_hwpt_paging_alloc() rolls back to allocate an iommu paging domain. Replace iommu_domain_alloc() with iommu_user_domain_alloc() to pass the device pointer along the path. Signed-off-by:
-
Lu Baolu authored
Commit <17de3f5f > ("iommu: Retire bus ops") removes iommu ops from bus. The iommu subsystem no longer relies on bus for operations. So the bus parameter in iommu_domain_alloc() is no longer relevant. Add a new interface named iommu_paging_domain_alloc(), which explicitly indicates the allocation of a paging domain for DMA managed by a kernel driver. The new interface takes a device pointer as its parameter, that better aligns with the current iommu subsystem. Signed-off-by:
Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20240610085555.88197-2-baolu.lu@linux.intel.com Signed-off-by:
-
- Jun 07, 2024
-
-
Louis Dalibard authored
At least ASUS Zenbook 14 (2023) and ASUS Zenbook 14 Pro (2023) are affected. The touchscreen reports a battery status of 0% and jumps to 1% when a stylus is used. The device ID was added and the battery ignore quirk was enabled for it. [jkosina@suse.com: reformatted changelog a bit] Signed-off-by:
Louis Dalibard <ontake@ontake.dev> Signed-off-by:
Jiri Kosina <jkosina@suse.com>
-
Johan Hovold authored
The Elan eKTH5015M touch controller found on the Lenovo ThinkPad X13s shares the VCC33 supply with other peripherals that may remain powered during suspend (e.g. when enabled as wakeup sources). The reset line is also wired so that it can be left deasserted when the supply is off. This is important as it avoids holding the controller in reset for extended periods of time when it remains powered, which can lead to increased power consumption, and also avoids leaking current through the X13s reset circuitry during suspend (and after driver unbind). Use the new 'no-reset-on-power-off' devicetree property to determine when reset needs to be asserted on power down. Notably this also avoids wasting power on machine variants without a touchscreen for which the driver would otherwise exit probe with reset asserted. Fixes: bd3cba00 ("HID: i2c-hid: elan: Add support for Elan eKTH6915 i2c-hid touchscreens") Cc: <stable@vger.kernel.org> # 6.0 Cc: Douglas Anderson <dianders@chromium.org> Tested-by:
Steev Klimaszewski <steev@kali.org> Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20240507144821.12275-5-johan+linaro@kernel.org Signed-off-by:
Benjamin Tissoires <bentiss@kernel.org>
-
Aseda Aboagye authored
HUTRR94 added support for a new usage titled "System Do Not Disturb" which toggles a system-wide Do Not Disturb setting. This commit simply adds a new event code for the usage. Signed-off-by:
Aseda Aboagye <aaboagye@chromium.org> Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Link: https://lore.kernel.org/r/Zl-gUHE70s7wCAoB@google.com Signed-off-by:
-
Aseda Aboagye authored
HUTRR116 added support for a new usage titled "System Accessibility Binding" which toggles a system-wide bound accessibility UI or command. This commit simply adds a new event code for the usage. Signed-off-by:
-
Andrew Ballance authored
syzbot reported a potential read out of bounds in asus_report_fixup. this patch adds checks so that a read out of bounds will not occur Signed-off-by:
Andrew Ballance <andrewjballance@gmail.com> Reported-by:
<syzbot+07762f019fd03d01f04c@syzkaller.appspotmail.com> Closes: https://syzkaller.appspot.com/bug?extid=07762f019fd03d01f04c Fixes: 59d2f5b7 ("HID: asus: fix more n-key report descriptors if n-key quirked") Link: https://lore.kernel.org/r/20240602085023.1720492-1-andrewjballance@gmail.com Signed-off-by:
-
Jeff Johnson authored
On x86, make allmodconfig && make W=1 C=1 reports: WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-gw-pld.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-mc33880.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-pcf857x.o Add the missing invocations of the MODULE_DESCRIPTION() macro, including the one missing in gpio-pl061.c, which is not built for x86. Signed-off-by:
Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://lore.kernel.org/r/20240606-md-drivers-gpio-v1-1-cb42d240ca5c@quicinc.com Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
-
- Jun 06, 2024
-
-
Michael Ellerman authored
The pata_macio driver advertises a max_segment_size of 0xff00, because the hardware doesn't cope with requests >= 64K. However the SCSI core requires max_segment_size to be at least PAGE_SIZE, which is a problem for pata_macio when the kernel is built with 64K pages. In older kernels the SCSI core would just increase the segment size to be equal to PAGE_SIZE, however since the commit tagged below it causes a warning and the device fails to probe: WARNING: CPU: 0 PID: 26 at block/blk-settings.c:202 .blk_validate_limits+0x2f8/0x35c CPU: 0 PID: 26 Comm: kworker/u4:1 Not tainted 6.10.0-rc1 #1 Hardware name: PowerMac7,2 PPC970 0x390202 PowerMac ... NIP .blk_validate_limits+0x2f8/0x35c LR .blk_alloc_queue+0xc0/0x2f8 Call Trace: .blk_alloc_queue+0xc0/0x2f8 .blk_mq_alloc_queue+0x60/0xf8 .scsi_alloc_sdev+0x208/0x3c0 .scsi_probe_and_add_lun+0x314/0x52c .__scsi_add_device+0x170/0x1a4 .ata_scsi_scan_host+0x2bc/0x3e4 ... -
Aleksandr Mishin authored
In case of region creation fail in ipc_devlink_create_region(), previously created regions delete process starts from tainted pointer which actually holds error code value. Fix this bug by decreasing region index before delete. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 4dcd183f ("net: wwan: iosm: devlink registration") Signed-off-by:
Aleksandr Mishin <amishin@t-argos.ru> Acked-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240604082500.20769-1-amishin@t-argos.ru Signed-off-by:
Paolo Abeni <pabeni@redhat.com>
-
- Jun 05, 2024
-
-
Ian Forbes authored
These pointers are frequently the same and memcmp does not compare the pointers before comparing their contents so this was wasting cycles comparing 16 KiB of memory which will always be equal. Fixes: bb6780aa ("drm/vmwgfx: Diff cursors when using cmds") Signed-off-by:
Ian Forbes <ian.forbes@broadcom.com> Signed-off-by:
Zack Rusin <zack.rusin@broadcom.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240328190716.27367-1-ian.forbes@broadcom.com
-
Sasha Neftin authored
The commit 01cf893b ("net: intel: i40e/igc: Remove setting Autoneg in EEE capabilities") removed SUPPORTED_Autoneg field but left inappropriate ethtool_keee structure initialization. When "ethtool --show <device>" (get_eee) invoke, the 'ethtool_keee' structure was accidentally overridden. Remove the 'ethtool_keee' overriding and add EEE declaration as per IEEE specification that allows reporting Energy Efficient Ethernet capabilities. Examples: Before fix: ethtool --show-eee enp174s0 EEE settings for enp174s0: EEE status: not supported After fix: EEE settings for enp174s0: EEE status: disabled Tx LPI: disabled Supported EEE link modes: 100baseT/Full 1000baseT/Full 2500baseT/Full Fixes: 01cf893b ("net: intel: i40e/igc: Remove setting Autoneg in EEE capabilities") Suggested-by:
Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Naama Meir <naamax.meir@linux.intel.com> Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-6-e3563aa89b0c@intel.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Larysa Zaremba authored
ice_pf_dcb_recfg() re-maps queues to vectors with ice_vsi_map_rings_to_vectors(), which does not restore the previous state for XDP queues. This leads to no AF_XDP traffic after rebuild. Map XDP queues to vectors in ice_vsi_map_rings_to_vectors(). Also, move the code around, so XDP queues are mapped independently only through .ndo_bpf(). Fixes: 6624e780 ("ice: split ice_vsi_setup into smaller functions") Reviewed-by:
Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by:
Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by:
Chandan Kumar Rout <chandanx.rout@intel.com> Signed-off-by:
-
Larysa Zaremba authored
Commit 6624e780 ("ice: split ice_vsi_setup into smaller functions") has placed ice_vsi_free_q_vectors() after ice_destroy_xdp_rings() in the rebuild process. The behaviour of the XDP rings config functions is context-dependent, so the change of order has led to ice_destroy_xdp_rings() doing additional work and removing XDP prog, when it was supposed to be preserved. Also, dependency on the PF state reset flags creates an additional, fortunately less common problem: * PFR is requested e.g. by tx_timeout handler * .ndo_bpf() is asked to delete the program, calls ice_destroy_xdp_rings(), but reset flag is set, so rings are destroyed without deleting the program * ice_vsi_rebuild tries to delete non-existent XDP rings, because the program is still on the VSI * system crashes With a similar race, when requested to attach a program, ice_prepare_xdp_rings() can actually skip setting the program in the VSI and nevertheless report success. Instead of reverting to the old order of function calls, add an enum argument to both ice_prepare_xdp_rings() and ice_destroy_xdp_rings() in order to distinguish between calls from rebuild and .ndo_bpf(). Fixes: efc2214b ("ice: Add support for XDP") Reviewed-by:
Igor Bagnucki <igor.bagnucki@intel.com> Signed-off-by:
-
Larysa Zaremba authored
Referenced commit has introduced a bitmap to distinguish between ZC and copy-mode AF_XDP queues, because xsk_get_pool_from_qid() does not do this for us. The bitmap would be especially useful when restoring previous state after rebuild, if only it was not reallocated in the process. This leads to e.g. xdpsock dying after changing number of queues. Instead of preserving the bitmap during the rebuild, remove it completely and distinguish between ZC and copy-mode queues based on the presence of a device associated with the pool. Fixes: e102db78 ("ice: track AF_XDP ZC enabled queues in bitmap") Reviewed-by:
-
Jacob Keller authored
The ice driver reads data from the Shadow RAM portion of the NVM during initialization, including data used to identify the NVM image and device, such as the ETRACK ID used to populate devlink dev info fw.bundle. Currently it is using a fixed offset defined by ICE_CSS_HEADER_LENGTH to compute the appropriate offset. This worked fine for E810 and E822 devices which both have CSS header length of 330 words. Other devices, including both E825-C and E830 devices have different sizes for their CSS header. The use of a hard coded value results in the driver reading from the wrong block in the NVM when attempting to access the Shadow RAM copy. This results in the driver reporting the fw.bundle as 0x0 in both the devlink dev info and ethtool -i output. The first E830 support was introduced by commit ba20ecb1 ("ice: Hook up 4 E830 devices by adding their IDs") and the first E825-C support was introducted by commit f64e1894 ("ice: introduce new E825C devices family") The NVM actually contains the CSS header length embedded in it. Remove the hard coded value and replace it with logic to read the length from the NVM directly. This is more resilient against all existing and future hardware, vs looking up the expected values from a table. It ensures the driver will read from the appropriate place when determining the ETRACK ID value used for populating the fw.bundle_id and for reporting in ethtool -i. The CSS header length for both the active and inactive flash bank is stored in the ice_bank_info structure to avoid unnecessary duplicate work when accessing multiple words of the Shadow RAM. Both banks are read in the unlikely event that the header length is different for the NVM in the inactive bank, rather than being different only by the overall device family. Fixes: ba20ecb1 ("ice: Hook up 4 E830 devices by adding their IDs") Co-developed-by:
Paul Greenwalt <paul.greenwalt@intel.com> Signed-off-by:
Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by:
-
Jacob Keller authored
The ice_get_pfa_module_tlv() function iterates over the Type-Length-Value structures in the Preserved Fields Area (PFA) of the NVM. This is used by the driver to access data such as the Part Board Assembly identifier. The function uses simple logic to iterate over the PFA. First, the pointer to the PFA in the NVM is read. Then the total length of the PFA is read from the first word. A pointer to the first TLV is initialized, and a simple loop iterates over each TLV. The pointer is moved forward through the NVM until it exceeds the PFA area. The logic seems sound, but it is missing a key detail. The Preserved Fields Area length includes one additional final word. This is documented in the device data sheet as a dummy word which contains 0xFFFF. All NVMs have this extra word. If the driver tries to scan for a TLV that is not in the PFA, it will read past the size of the PFA. It reads and interprets the last dummy word of the PFA as a TLV with type 0xFFFF. It then reads the word following the PFA as a length. The PFA resides within the Shadow RAM portion of the NVM, which is relatively small. All of its offsets are within a 16-bit size. The PFA pointer and TLV pointer are stored by the driver as 16-bit values. In almost all cases, the word following the PFA will be such that interpreting it as a length will result in 16-bit arithmetic overflow. Once overflowed, the new next_tlv value is now below the maximum offset of the PFA. Thus, the driver will continue to iterate the data as TLVs. In the worst case, the driver hits on a sequence of reads which loop back to reading the same offsets in an endless loop. To fix this, we need to correct the loop iteration check to account for this extra word at the end of the PFA. This alone is sufficient to resolve the known cases of this issue in the field. However, it is plausible that an NVM could be misconfigured or have corrupt data which results in the same kind of overflow. Protect against this by using check_add_overflow when calculating both the maximum offset of the TLVs, and when calculating the next_tlv offset at the end of each loop iteration. This ensures that the driver will not get stuck in an infinite loop when scanning the PFA. Fixes: e961b679 ("ice: add board identifier info to devlink .info_get") Co-developed-by:
-
Dr. David Alan Gilbert authored
'vmw_stdu_dma' is unused since commit 39985eea ("drm/vmwgfx: Abstract placement selection") Remove it. Signed-off-by:
Dr. David Alan Gilbert <linux@treblig.org> Signed-off-by:
-
Ian Forbes authored
drm_crtc_helper_funcs::atomic_disable can be called even when the CRTC is still enabled. This can occur when the mode changes or the CRTC is set as inactive. In the case where the CRTC is being set as inactive we only want to blank the screen. The Screen Target should remain intact as long as the mode has not changed and CRTC is enabled. This fixes a bug with GDM where locking the screen results in a permanent black screen because the Screen Target is no longer defined. Fixes: 7b006203 ("drm/vmwgfx: Implement virtual crc generation") Signed-off-by:
Martin Krastev <martin.krastev@broadcom.com> Signed-off-by:
-
Ian Forbes authored
Use the same standard abbreviation KiB instead of incorrect variants. Signed-off-by:
-
Ian Forbes authored
STDU has its own mode_valid function now so this logic can be removed from the generic version. Fixes: 935f7950 ("drm/vmwgfx: Refactor drm connector probing for display modes") Signed-off-by:
-
Ian Forbes authored
This limit became a hard cap starting with the change referenced below. Surface creation on the device will fail if the requested size is larger than this limit so altering the value arbitrarily will expose modes that are too large for the device's hard limits. Fixes: 7ebb47c9 ("drm/vmwgfx: Read new register for GB memory when available") Signed-off-by:
-
Ian Forbes authored
SVGA requires individual surfaces to fit within graphics memory (max_mob_pages) which means that modes with a final buffer size that would exceed graphics memory must be pruned otherwise creation will fail. Additionally llvmpipe requires its buffer height and width to be a multiple of its tile size which is 64. As a result we have to anticipate that llvmpipe will round up the mode size passed to it by the compositor when it creates buffers and filter modes where this rounding exceeds graphics memory. This fixes an issue where VMs with low graphics memory (< 64MiB) configured with high resolution mode boot to a black screen because surface creation fails. Fixes: d947d1b7 ("drm/vmwgfx: Add and connect connector helper function") Signed-off-by:
-
Karol Kolacinski authored
On failed verification of PTP clock pin, error message prints channel number instead of pin index after "pin", which is incorrect. Fix error message by adding channel number to the message and printing pin number instead of channel number. Fixes: 6092315d ("ptp: introduce programmable pins.") Signed-off-by:
Karol Kolacinski <karol.kolacinski@intel.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/20240604120555.16643-1-karol.kolacinski@intel.com Signed-off-by:
-
Aleksandr Mishin authored
In case of flow rule creation fail in mlx5_lag_create_port_sel_table(), instead of previously created rules, the tainted pointer is deleted deveral times. Fix this bug by using correct flow rules pointers. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 352899f3 ("net/mlx5: Lag, use buckets in hash mode") Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20240604100552.25201-1-amishin@t-argos.ru Signed-off-by:
-
Andreas Hindborg authored
Block size should be between 512 and PAGE_SIZE and be a power of 2. The current check does not validate this, so update the check. Without this patch, null_blk would Oops due to a null pointer deref when loaded with bs=1536 [1]. Link: https://lore.kernel.org/all/87wmn8mocd.fsf@metaspace.dk/ Signed-off-by:
Andreas Hindborg <a.hindborg@samsung.com> Reviewed-by:
Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20240603192645.977968-1-nmi@metaspace.dk [axboe: remove unnecessary braces and != 0 check] Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Tasos Sahanidis authored
Flexible arrays used [1] instead of []. Replace the former with the latter to resolve multiple UBSAN warnings observed on boot with a BONAIRE card. In addition, use the __counted_by attribute where possible to hint the length of the arrays to the compiler and any sanitizers. Signed-off-by:
Tasos Sahanidis <tasos@tasossah.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Mario Limonciello authored
commit cd94d1b1 ("dm/amd/pm: Fix problems with reboot/shutdown for some SMU 13.0.4/13.0.11 users") attempted to fix shutdown issues that were reported since commit 31729e8c ("drm/amd/pm: fixes a random hang in S4 for SMU v13.0.4/11") but caused issues for some people. Adjust the workaround flow to properly only apply in the S4 case: -> For shutdown go through SMU_MSG_PrepareMp1ForUnload -> For S4 go through SMU_MSG_GfxDeviceDriverReset and SMU_MSG_PrepareMp1ForUnload Reported-and-tested-by:
lectrode <electrodexsnet@gmail.com> Closes: https://github.com/void-linux/void-packages/issues/50417 Cc: stable@vger.kernel.org Fixes: cd94d1b1 ("dm/amd/pm: Fix problems with reboot/shutdown for some SMU 13.0.4/13.0.11 users") Reviewed-by:
Tim Huang <Tim.Huang@amd.com> Signed-off-by:
Mario Limonciello <mario.limonciello@amd.com> Signed-off-by:
-
Shay Drory authored
Currently, if teardown_hca fails to execute during driver removal, mlx5 does not stop the health timer. Afterwards, mlx5 continue with driver teardown. This may lead to a UAF bug, which results in page fault Oops[1], since the health timer invokes after resources were freed. Hence, stop the health monitor even if teardown_hca fails. [1] mlx5_core 0000:18:00.0: E-Switch: Unload vfs: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) mlx5_core 0000:18:00.0: E-Switch: Disable: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) mlx5_core 0000:18:00.0: E-Switch: Disable: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) mlx5_core 0000:18:00.0: E-Switch: cleanup mlx5_core 0000:18:00.0: wait_func:1155:(pid 1967079): TEARDOWN_HCA(0x103) timeout. Will cause a leak of a command resource mlx5_core 0000:18:00.0: mlx5_function_close:1288:(pid 1967079): tear_down_hca failed, skip cleanup BUG: unable to handle page fault for address: ffffa26487064230 PGD 100c00067 P4D 100c00067 PUD 100e5a067 PMD 105ed7067 PTE 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 0 Comm: swapper/0 Tainted: G OE ------- --- 6.7.0-68.fc38.x86_64 #1 Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0013.121520200651 12/15/2020 RIP: 0010:ioread32be+0x34/0x60 RSP: 0018:ffffa26480003e58 EFLAGS: 00010292 RAX: ffffa26487064200 RBX: ffff9042d08161a0 RCX: ffff904c108222c0 RDX: 000000010bbf1b80 RSI: ffffffffc055ddb0 RDI: ffffa26487064230 RBP: ffff9042d08161a0 R08: 0000000000000022 R09: ffff904c108222e8 R10: 0000000000000004 R11: 0000000000000441 R12: ffffffffc055ddb0 R13: ffffa26487064200 R14: ffffa26480003f00 R15: ffff904c108222c0 FS: 0000000000000000(0000) GS:ffff904c10800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffa26487064230 CR3: 00000002c4420006 CR4: 00000000007706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <IRQ> ? __die+0x23/0x70 ? page_fault_oops+0x171/0x4e0 ? exc_page_fault+0x175/0x180 ? asm_exc_page_fault+0x26/0x30 ? __pfx_poll_health+0x10/0x10 [mlx5_core] ? __pfx_poll_health+0x10/0x10 [mlx5_core] ? ioread32be+0x34/0x60 mlx5_health_check_fatal_sensors+0x20/0x100 [mlx5_core] ? __pfx_poll_health+0x10/0x10 [mlx5_core] poll_health+0x42/0x230 [mlx5_core] ? __next_timer_interrupt+0xbc/0x110 ? __pfx_poll_health+0x10/0x10 [mlx5_core] call_timer_fn+0x21/0x130 ? __pfx_poll_health+0x10/0x10 [mlx5_core] __run_timers+0x222/0x2c0 run_timer_softirq+0x1d/0x40 __do_softirq+0xc9/0x2c8 __irq_exit_rcu+0xa6/0xc0 sysvec_apic_timer_interrupt+0x72/0x90 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:cpuidle_enter_state+0xcc/0x440 ? cpuidle_enter_state+0xbd/0x440 cpuidle_enter+0x2d/0x40 do_idle+0x20d/0x270 cpu_startup_entry+0x2a/0x30 rest_init+0xd0/0xd0 arch_call_rest_init+0xe/0x30 start_kernel+0x709/0xa90 x86_64_start_reservations+0x18/0x30 x86_64_start_kernel+0x96/0xa0 secondary_startup_64_no_verify+0x18f/0x19b ---[ end trace 0000000000000000 ]--- Fixes: 9b98d395 ("net/mlx5: Start health poll at earlier stage of driver load") Signed-off-by:
Shay Drory <shayd@nvidia.com> Reviewed-by:
Moshe Shemesh <moshe@nvidia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Moshe Shemesh authored
In case pci channel becomes offline the driver should not wait for PCI reads during health dump and recovery flow. The driver has timeout for each of these loops trying to read PCI, so it would fail anyway. However, in case of recovery waiting till timeout may cause the pci error_detected() callback fail to meet pci_dpc_recovered() wait timeout. Fixes: b3bd076f ("net/mlx5: Report devlink health on FW fatal issues") Signed-off-by:
-
Frank Wunderlich authored
The mainline MTK ethernet driver suffers long time from rarly but annoying tx queue timeouts. We think that this is caused by fixed dma sizes hardcoded for all SoCs. We suspect this problem arises from a low level of free TX DMADs, the TX Ring alomost full. The transmit timeout is caused by the Tx queue not waking up. The Tx queue stops when the free counter is less than ring->thres, and it will wake up once the free counter is greater than ring->thres. If the CPU is too late to wake up the Tx queues, it may cause a transmit timeout. Therefore, we increased the TX and RX DMADs to improve this error situation. Use the dma-size implementation from SDK in a per SoC manner. In difference to SDK we have no RSS feature yet, so all RX/TX sizes should be raised from 512 to 2048 byte except fqdma on mt7988 to avoid the tx timeout issue. Fixes: 656e7052 ("net-next: mediatek: add support for MT7623 ethernet") Suggested-by:
Daniel Golle <daniel@makrotopia.org> Signed-off-by:
Frank Wunderlich <frank-w@public-files.de> Reviewed-by:
-
Daniel Borkmann authored
Commit f58f45c1 ("vxlan: drop packets from invalid src-address") has recently been added to vxlan mainly in the context of source address snooping/learning so that when it is enabled, an entry in the FDB is not being created for an invalid address for the corresponding tunnel endpoint. Before commit f58f45c1 vxlan was similarly behaving as geneve in that it passed through whichever macs were set in the L2 header. It turns out that this change in behavior breaks setups, for example, Cilium with netkit in L3 mode for Pods as well as tunnel mode has been passing before the change in f58f45c1 for both vxlan and geneve. After mentioned change it is only passing for geneve as in case of vxlan packets are dropped due to vxlan_set_mac() returning false as source and destination macs are zero which for E/W traffic via tunnel is totally fine. Fix it by only opting into the is_valid_ether_addr() check in vxlan_set_mac() when in fact source address snooping/learning is actually enabled in vxlan. This is done by moving the check into vxlan_snoop(). With this change, the Cilium connectivity test suite passes again for both tunnel flavors. Fixes: f58f45c1 ("vxlan: drop packets from invalid src-address") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Cc: David Bauer <mail@david-bauer.net> Cc: Ido Schimmel <idosch@nvidia.com> Cc: Nikolay Aleksandrov <razor@blackwall.org> Cc: Martin KaFai Lau <martin.lau@kernel.org> Reviewed-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by:
David Bauer <mail@david-bauer.net> Signed-off-by:
-
Taehee Yoo authored
In the XDP_TX path, ionic driver sends a packet to the TX path with rx page and corresponding dma address. After tx is done, ionic_tx_clean() frees that page. But RX ring buffer isn't reset to NULL. So, it uses a freed page, which causes kernel panic. BUG: unable to handle page fault for address: ffff8881576c110c PGD 773801067 P4D 773801067 PUD 87f086067 PMD 87efca067 PTE 800ffffea893e060 Oops: Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN NOPTI CPU: 1 PID: 25 Comm: ksoftirqd/1 Not tainted 6.9.0+ #11 Hardware name: ASUS System Product Name/PRIME Z690-P D4, BIOS 0603 11/01/2021 RIP: 0010:bpf_prog_f0b8caeac1068a55_balancer_ingress+0x3b/0x44f Code: 00 53 41 55 41 56 41 57 b8 01 00 00 00 48 8b 5f 08 4c 8b 77 00 4c 89 f7 48 83 c7 0e 48 39 d8 RSP: 0018:ffff888104e6fa28 EFLAGS: 00010283 RAX: 0000000000000002 RBX: ffff8881576c1140 RCX: 0000000000000002 RDX: ffffffffc0051f64 RSI: ffffc90002d33048 RDI: ffff8881576c110e RBP: ffff888104e6fa88 R08: 0000000000000000 R09: ffffed1027a04a23 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8881b03a21a8 R13: ffff8881589f800f R14: ffff8881576c1100 R15: 00000001576c1100 FS: 0000000000000000(0000) GS:ffff88881ae00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffff8881576c110c CR3: 0000000767a90000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? __die+0x20/0x70 ? page_fault_oops+0x254/0x790 ? __pfx_page_fault_oops+0x10/0x10 ? __pfx_is_prefetch.constprop.0+0x10/0x10 ? search_bpf_extables+0x165/0x260 ? fixup_exception+0x4a/0x970 ? exc_page_fault+0xcb/0xe0 ? asm_exc_page_fault+0x22/0x30 ? 0xffffffffc0051f64 ? bpf_prog_f0b8caeac1068a55_balancer_ingress+0x3b/0x44f ? do_raw_spin_unlock+0x54/0x220 ionic_rx_service+0x11ab/0x3010 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ? ionic_tx_clean+0x29b/0xc60 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ? __pfx_ionic_tx_clean+0x10/0x10 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ? __pfx_ionic_rx_service+0x10/0x10 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ? ionic_tx_cq_service+0x25d/0xa00 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ? __pfx_ionic_rx_service+0x10/0x10 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ionic_cq_service+0x69/0x150 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] ionic_txrx_napi+0x11a/0x540 [ionic 9180c3001ab627d82bbc5f3ebe8a0decaf6bb864] __napi_poll.constprop.0+0xa0/0x440 net_rx_action+0x7e7/0xc30 ? __pfx_net_rx_action+0x10/0x10 Fixes: 8eeed837 ("ionic: Add XDP_TX support") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Reviewed-by:
Shannon Nelson <shannon.nelson@amd.com> Reviewed-by:
Brett Creeley <brett.creeley@amd.com> Signed-off-by:
-
Tristram Ha authored
KSZ8061 needs to write to a MMD register at driver initialization to fix an errata. This worked in 5.0 kernel but not in newer kernels. The issue is the main phylib code no longer resets PHY at the very beginning. Calling phy resuming code later will reset the chip if it is already powered down at the beginning. This wipes out the MMD register write. Solution is to implement a phy resume function for KSZ8061 to take care of this problem. Fixes: 232ba3a5 ("net: phy: Micrel KSZ8061: link failure after cable connect") Signed-off-by:
Tristram Ha <tristram.ha@microchip.com> Signed-off-by:
-
Subbaraya Sundeep authored
PF mcam entries has to be at low priority always so that VF can install longest prefix match rules at higher priority. This was taken care currently but when priority allocation wrt reference entry is requested then entries are allocated from mid-zone instead of low priority zone. Fix this and always allocate entries from low priority zone for PFs. Fixes: 7df5b4b2 ("octeontx2-af: Allocate low priority entries for PF") Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Reviewed-by:
-
Ard Biesheuvel authored
The EFI runtime wrappers are a sandbox for calling into EFI runtime services, which are invoked using indirect calls. When running with kCFI enabled, the compiler will require the target of any indirect call to be type annotated. Given that the EFI runtime services prototypes and calling convention are governed by the EFI spec, not the Linux kernel, adding such type annotations for firmware routines is infeasible, and so the compiler must be informed that prototype validation should be omitted. Add the __nocfi annotation at the appropriate places in the EFI runtime wrapper code to achieve this. Note that this currently only affects 32-bit ARM, given that other architectures that support both kCFI and EFI use an asm wrapper to call EFI runtime services, and this hides the indirect call from the compiler. Fixes: 1a4fec49 ("ARM: 9392/2: Support CLANG CFI") Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Tested-by:
Nathan Chancellor <nathan@kernel.org> Signed-off-by:
Ard Biesheuvel <ardb@kernel.org>
-
- Jun 04, 2024
-
-
Tony Luck authored
New CPU #defines encode vendor and family as well as model. Link: https://lore.kernel.org/all/20240520224620.9480-4-tony.luck@intel.com/ Signed-off-by:
Tony Luck <tony.luck@intel.com> Reviewed-by:
Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by:
-
Jan Beulich authored
tpm_tis_core_init() may fail before tpm_tis_probe_irq_single() is called, in which case tpm_tis_remove() unconditionally calling flush_work() is triggering a warning for .func still being NULL. Cc: stable@vger.kernel.org # v6.5+ Fixes: 481c2d14 ("tpm,tpm_tis: Disable interrupts after 1000 unhandled IRQs") Signed-off-by:
Jan Beulich <jbeulich@suse.com> Reviewed-by:
-
