diff --git a/boards/beaglev/fire/05-demos.rst b/boards/beaglev/fire/05-demos.rst
index ad003fa2421b6a35b6beb8ca5f34e62ec61daac1..56b95dc0c02c5dc147c305615bbcc5b84d0c2315 100644
--- a/boards/beaglev/fire/05-demos.rst
+++ b/boards/beaglev/fire/05-demos.rst
@@ -18,3 +18,4 @@ Demos
     demos-and-tutorials/mchp-fpga-tools-installation-guide
     demos-and-tutorials/gateware/index
     demos-and-tutorials/gateware/how-to-find-out-whats-on-the-board
+    demos-and-tutorials/gateware/gateware-full-flow
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/gateware-full-flow.rst b/boards/beaglev/fire/demos-and-tutorials/gateware/gateware-full-flow.rst
new file mode 100644
index 0000000000000000000000000000000000000000..20478dd08d1118734c495e06096a02b17cb4e1b8
--- /dev/null
+++ b/boards/beaglev/fire/demos-and-tutorials/gateware/gateware-full-flow.rst
@@ -0,0 +1,75 @@
+Gateware Full Build Flow
+########################
+
+Introduction
+============
+
+The BeagleV-Fire gateware is made up of several components:
+
+- Digital design for the FPGA fabric. This can a combination of:
+  
+  - HDL/Verilog source code 
+  - TCL scripts configuring IP blocks
+  - TCL scripts stiching IP blocks together
+  - Microprocessor Subsystem (MSS) configuration describing the MSS port list
+  - pin, placement and timing constraints
+- Microprocessor Subsystem (MSS) configuration containing MSS configuration register values
+- A zero stage bootloader (HSS) that will:
+  
+  - Provision the MSS configuration into chip configuration registers:
+  
+    - Setup clocks
+    - Configure memory controllers
+    - Configure IOs
+    - Configure transceivers
+  
+  - Retrieve the next boot stage from eMMc and hand-over to the next boot stage (e.g. u-boot)
+  - Make the board appear as a USB mass-storage for populating the eMMC with secondary boot-loader and operating system image.
+- A set of device tree ovelays describing the content of the FPGA fabric.
+
+Of course all these components need to be in synch with each other for the system to work properly.
+This is the reason for using a gateware build system rather than building and tracking each component individually.
+
+.. figure:: media/Gateware-Flow-bitstream-builder-full-picture.png
+    :align: center
+    :alt: BeagleV-Fire Gateware Full Build Flow
+
+Programming artifacts
+=====================
+
+The BeagleV-Fire gateware builder produces two programming artifacts:
+
+- A bitstream containing the FPGA fabric and eNVM programming
+- A device tree overlay describing the FPGA content.
+
+These two artifacts are packaged differently depending on the programming method. They are merged
+into a single programming file for DirectC (.dat) and FlashPro Express (.job). They are kept
+separate for Linux programming (mpfs_bitstream.spi and mpfs_dtbo.spi).
+
+Programming BeagleV-Fire with new gateware
+==========================================
+
+There are several methods possible for programming the BeagleV-Fire with new gateware:
+
+- Linux script executed on the BeagleV-Fire board.
+- Running DirectC on anothe single board computer
+- Using Microchip's FlashPro Express
+
+Linux script
+------------
+This is the recommended approach. It does not require any additional hardware. Simply run the script
+located in /usr/share/beagleboard/gateware. You should use this methods unless you have soft-bricked
+your BeagleV-Fire.
+
+DirectC
+-------
+This approach uses a single board computer (SBC) connected to the BeagleV-Fire JTAG port. The SBC
+bit-bangs the FPGA programming protocol over GPIOs. This approach is only required for recovering
+a soft-bricked BeagleV-Fire.
+
+FlashPro Express
+----------------
+This approach uses Microchip's FlashPro Express programming software and a FlashPro6 JTAG programmer.
+I would recommend using the Linux script even if you are an existing Microchip FPGA user with all the
+tools. This approach makes most sense when doing bare metal software development and already have a
+FlashPro programmer and don't care about device tree overlays.
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/media/Gateware-Flow-bitstream-builder-full-picture.png b/boards/beaglev/fire/demos-and-tutorials/gateware/media/Gateware-Flow-bitstream-builder-full-picture.png
index 7d37d3d8d7cb97d37cbe908ac39f4fae7c068d55..e9517d622f82ca36ae5472721a0bba6d59e654a7 100644
Binary files a/boards/beaglev/fire/demos-and-tutorials/gateware/media/Gateware-Flow-bitstream-builder-full-picture.png and b/boards/beaglev/fire/demos-and-tutorials/gateware/media/Gateware-Flow-bitstream-builder-full-picture.png differ