diff --git a/boards/beaglev/fire/05-demos.rst b/boards/beaglev/fire/05-demos.rst
index 45e44d6ba1132d8d8f856f28a3badf6746b6f92d..b7c8b1ea46812d0a634b8224c7087e3fb75ca42b 100644
--- a/boards/beaglev/fire/05-demos.rst
+++ b/boards/beaglev/fire/05-demos.rst
@@ -24,5 +24,7 @@ Demos
demos-and-tutorials/gateware/customize-cape-gateware-verilog
demos-and-tutorials/gateware/running-the-bitstream-builder-on-windows
demos-and-tutorials/gateware/exploring-gateware-design-libero
+ demos-and-tutorials/gateware/gateware-design-simulation-libero
demos-and-tutorials/gateware/comms-cape-gateware-usage
demos-and-tutorials/gateware/axi-apb-interfaces-demo
+
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/gateware-design-simulation-libero.rst b/boards/beaglev/fire/demos-and-tutorials/gateware/gateware-design-simulation-libero.rst
new file mode 100644
index 0000000000000000000000000000000000000000..49ee5e7600c1393f58695048e18e31f5299706f1
--- /dev/null
+++ b/boards/beaglev/fire/demos-and-tutorials/gateware/gateware-design-simulation-libero.rst
@@ -0,0 +1,125 @@
+.. _beaglev-fire-gateware-design-simulation-libero:
+
+Simulating Gateware Design with Libero
+##########################################
+
+In this demonstration, we will have a look at simulating the gateware design in Libero. Through simulations,
+one can verify the functionality of the design before implementing it on the hardware. The simulation is done using the ModelSim simulator,
+which is integrated with Libero. The gateware design that we will simulate is the blinky LED design, present in the ``VERILOG_TUTORIAL`` gateware option.
+
+
+Prerequisites
+*************
+
+#. Libero SoC 2022 or later. You can follow this guide to install Libero SoC: :ref:`beaglev-fire-mchp-fpga-tools-installation-guide`.
+#. A copy of the `gateware repository <https://openbeagle.org/beaglev-fire/gateware/>`_.
+#. The ``setup_microchip_tools.sh`` file, to start the license server and set the environment variables. The setup of this script is also covered in the installation guide.
+
+Setting up ModelSim
+*******************
+
+Modelsim requires certain libraries to be present in the system, which might not be installed by default. You can check if ModelSim is working by:
+
+.. code-block:: bash
+
+ source setup_microchip_tools.sh
+ $LIBERO_INSTALL_DIR/ModelSimPro/linuxacoem/vsim
+
+If ModelSim is not working due to missing libraries, you might see an error message like:
+
+.. code-block:: bash
+
+ vsim: error while loading shared libraries: libXft.so.2: cannot open shared object file: No such file or directory
+
+To fix this, you can install the required libraries using the following command:
+
+.. code-block:: bash
+
+ sudo apt-get install libxft2 libxft2:i386 lib32ncurses5
+
+If you still cannot run ModelSim, you can try fixes from this `guide <https://profile.iiita.ac.in/bibhas.ghoshal/COA_2020/Lab/ModelSim%20Linux%20installation.html>`_.
+
+Simulating the Blinky LED Design
+*********************************
+
+To start with the simulation, we must first compile the gateware design. The blinky LED design is present in
+the ``VERILOG_TUTORIAL`` gateware option. To compile the design, follow the steps below:
+
+#. First, compile the gateware design using the following command:
+
+.. code-block:: bash
+
+ cd gateware
+ python build-bitstream.py custom-fpga-design/my_custom_fpga_design.yaml
+
+#. Once the design is compiled, open the Libero SoC software and select the created project. You can find the project in the ``work/libero`` directory.
+
+#. Once the project is opened, your window should look something like this. In front of you will be the overview of the gateware design, and on the left you will have multiple tabs showing the design hierarchy, design flow, etc.
+
+.. figure:: images/simulation-demo/libero-overview.png
+ :alt: Libero SoC Overview
+
+#. For the simulation, testbench files will need to be set up, which will be used to simulate the design. This can be done from the stimulus hierarchy. However, for this example we will be using the default testbench files provided by libero.
+
+#. To set up the simulation, go to the ``Design Flow`` tab and right click on the ``Simulate`` button to select ``Open Interactively``.
+
+.. figure:: images/simulation-demo/libero-start-modelsim.png
+ :alt: Simulate Button
+ :width: 60%
+ :align: center
+
+#. Before starting modelsim, Libero will ask you to add any additional files that you want to include in the simulation. For now, let's go with the ones that came with the design and it's IPs.
+
+.. figure:: images/simulation-demo/libero-add-testbench.png
+ :alt: Add Testbench
+ :width: 60%
+ :align: center
+
+#. Once the simulation is started, you will see the ModelSim window open up.
+
+.. figure:: images/simulation-demo/modelsim-structure.png
+ :alt: ModelSim Window
+ :align: center
+
+Exploring ModelSim and Running the simulations
+**********************************************
+
+Looking at the modelsim window, there are four main sections to look at:
+
+#. The top left section shows the design hierarchy. This is where you can see the design modules and their instances.
+
+#. The section beside the design hierarchy is the object hierarchy. This shows the objects in the design, including the signals and variables.
+
+#. At the top, you should see the simulation toolbar. This is where you can run the simulations, add breakpoints, etc.
+
+#. At the bottom, you should see the transcript window. This is where you can see the simulation logs. This also acts as a command line interface for ModelSim.
+
+#. The far right section is the waveform window. This is where you can see the waveforms of the signals in the design.
+
+You can add signals to the waveform window by right clicking on the signal in the object hierarchy and selecting ``Add to Wave``.
+Once added, you can run the simulation by clicking on the ``Run`` button in the simulation toolbar. The simulation will run for a few nano seconds as specified
+in the toolbar beside the ``Run`` button.
+
+.. figure:: images/simulation-demo/modelsim-adding-waves.png
+ :alt: ModelSim Waveform
+ :align: center
+
+Once the simulation is complete, you can see the waveforms of the signals in the waveform window.
+
+If you want to automate addition of signals to the waveform, you see the output of each GUI command in the transcript window. You can use these commands to automate the process.
+Just put the commands in a file with a ``.do`` extension and run the file using the ``do`` command in the transcript window.
+
+An example of a ``.do`` file is shown below:
+
+.. code-block:: tcl
+
+ add wave -noupdate /tb_top/clk
+ add wave -noupdate /tb_top/rst
+ add wave -noupdate /tb_top/led
+
+ run 100 ns
+
+A default ``run.do`` script is created at the following path - ``work/libero/simulation`` - when a simulation is run. You can use this file as a starter file
+for creating your own scripts as well as for understanding how the initial simulation is set-up.
+
+Good luck with your simulations!
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-add-testbench.png b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-add-testbench.png
new file mode 100644
index 0000000000000000000000000000000000000000..812ee030328147fb5d4fc6525048e98ee3f40a31
Binary files /dev/null and b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-add-testbench.png differ
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-overview.png b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-overview.png
new file mode 100644
index 0000000000000000000000000000000000000000..1036a1cf360358c1e2e280deb1cad3a3838fbf54
Binary files /dev/null and b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-overview.png differ
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-start-modelsim.png b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-start-modelsim.png
new file mode 100644
index 0000000000000000000000000000000000000000..55453d2bcb959d3b052b49d85706bc631c101929
Binary files /dev/null and b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/libero-start-modelsim.png differ
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-adding-waves.png b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-adding-waves.png
new file mode 100644
index 0000000000000000000000000000000000000000..05b755db19f4025b843e2e3a05f8419fed8b3c10
Binary files /dev/null and b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-adding-waves.png differ
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-console.png b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-console.png
new file mode 100644
index 0000000000000000000000000000000000000000..96d901c54150f01a5cfd963a32ccb8b64d489bd7
Binary files /dev/null and b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-console.png differ
diff --git a/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-structure.png b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-structure.png
new file mode 100644
index 0000000000000000000000000000000000000000..9b4e7cfab627d0ecbdc5a393dfeab19c545a675f
Binary files /dev/null and b/boards/beaglev/fire/demos-and-tutorials/gateware/images/simulation-demo/modelsim-structure.png differ